 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 3161 HALL-EFFECT SWITCH FOR 2-WIRE APPLICATIONS This Hall-effect switch is a monolithic integrated circuit designed to operate continuously over extended temperatures to +85C. The unipolar switching characteristic makes this device ideal for use with a simple bar or rod magnet. The A3161ELT and A3161EUA are identical except for package. Each device includes a voltage regulator for operation with supply voltages of 3.5 to 25 volts, reverse battery protection diode, quadratic Hall-voltage generator, temperature compensation circuitry, small-signal amplifier, Schmitt trigger, and a constant-current open-collector output. Noise radiation is limited by control of the output current slew rate. Two package styles provide a magnetically optimized package for most applications. Suffix `LT' is a miniature SOT-89/TO-243AA transistor package for surface-mount applications; suffix `UA' is a threelead ultra-mini SIP for through-hole mounting. Data Sheet 27621.30B V X CC 1 2 3 GROUND Dwg. PH-003-3 OUTPUT SUPPLY FEATURES and BENEFITS s s s s s s s s s Pinning is shown viewed from branded side. ABSOLUTE MAXIMUM RATINGS at TA = +25C Supply Voltage, VCC Continuous ................................. 28 V Surge (tw 100 ms) .................... 40 V Reverse Battery Voltage, VRCC Continuous ................................ -25 V Surge (tw 100 ms) ................... -40 V Magnetic Flux Density, B ....... Unlimited Output OFF Voltage, VOUT .............. 28 V Operating Temperature Range, TA ............................. -40C to +85C Storage Temperature Range, TS ........................... -65C to +170C Internal Current Regulator for 2-Wire Operation Output Slew Rate Controlled 3.5 V to 25 V Operation ... Needs Only An Unregulated Supply Reverse Battery Protection Excellent Temp. Stability Activate with Small, Commercially Available Permanent Magnets Small Size Solid-State Reliability ... No Moving Parts Resistant to Physical Stress Always order by complete part number, e.g., A3161ELT . 3161 HALL-EFFECT SWITCH FOR 2-WIRE APPLICATIONS ELECTRICAL CHARACTERISTICS over operating voltage and temperature ranges. Limits Characteristic Supply Voltage Load Current (2-wire application) Symbol VCC IOUT + ICC Test Conditions Operating 3.5 V VOUT < 12 V, B < BRP VOUT 12 V, B < BRP B > BOP Output Current IOUT IOFF Output Saturation Voltage Output Slew Rate Output Settling Time VOUT di/dt tsd B < BRP VOUT = 24 V, B > BOP IOUT = 5 mA, B < BRP CL = 20 pF CL = 20 pF Min. 3.5 12 12 -- -- -- - -- -- Typ. -- 15 15 3.5 12 <1.0 0.9 7.0 -- Max. 25 17 19 5.0 -- 10 1.5 20 20 Units V mA mA mA mA A V mA/s s MAGNETIC CHARACTERISTICS over operating supply voltage range. Limits At TA = +25C Characteristic Operate Point (output turns OFF) Release Point (output turns ON) Hysteresis (BOP - BRP) Symbol BOP BRP Bhys Min. - 30 5.0 Typ. 130 110 20 Max. 160 - - Over Oper. Temp. Range Min. - 30 5.0 Typ. 130 110 20 Max. 160 - 80 Units G G G NOTE:Typical values are at TA = +25C and VCC = 12 V. FUNCTIONAL BLOCK DIAGRAM 1 VCC 3 OUTPUT REG. X 2 GROUND Dwg. FH-017 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright (c) 1998, 2002 Allegro MicroSystems, Inc. 3161 HALL-EFFECT SWITCH FOR 2-WIRE APPLICATIONS TYPICAL OPERATING CHARACTERISTICS SWITCH POINTS 200 TOTAL SUPPLY CURRENT 20 + I CC ) in mA VCC = 25 V 15 VCC = 3.5 V 150 B < BRP SWITCH POINT in GAUSS OPERATE POINT 100 RELEASE POINT TOTAL SUPPLY CURRENT (I OUT 10 50 5.0 VCC = 25 V VCC = 3.5 V 0 -50 B > BOP OVER OPER. VOLT. RANGE 0 -50 -25 0 25 50 75 100 125 150 -25 0 25 50 75 100 125 150 AMBIENT TEMPERATURE in C Dwg. GH-044-1 AMBIENT TEMPERATURE in C Dwg. GH-028-4 OUTPUT SATURATION VOLTAGE 1200 SAFE OPERATING AREA 30 MAXIMUM CONTINUOUS SUPPLY VOLTAGE in VOLTS 1000 25 SATURATION VOLTAGE in mV 800 20 PACKAGE SUFFIX CODE -UA 15 PACKAGE SUFFIX CODE -LT 10 600 400 200 IOUT = 5 mA VCC = 10 V 5 0 -50 0 -25 0 25 50 75 100 125 150 20 40 60 80 100 120 140 160 180 AMBIENT TEMPERATURE in C Dwg. GH-029-3 AMBIENT TEMPERATURE in C Dwg. GH-068 www.allegromicro.com 3161 HALL-EFFECT SWITCH FOR 2-WIRE APPLICATIONS SENSOR LOCATIONS Suffix "LT" ACTIVE AREA DEPTH 0.0305" 0.775 mm NOM 0.085" 2.16 mm 0.045" 1.14 mm OPERATION The output of these devices (pin 3) switches OFF when the magnetic field at the Hall sensor exceeds the operate point threshold (BOP). When the magnetic field is reduced to below the release point threshold (BRP), the device output switches ON. The difference in the magnetic operate and release points is called the hysteresis (Bhys) of the device. This built-in hysteresis allows clean switching of the output even in the presence of external mechanical vibration and electrical noise. 15 A 1 2 3 12 BOP Dwg. MH-008-7A OUTPUT CURRENT in mA 9.0 Suffix "UA" ACTIVE AREA DEPTH 0.0195" 0.50 mm NOM 0.078" 1.98 mm 6.0 TA = +25C 3.0 BRP A BRANDED SURFACE 1 2 3 0.054" 1.36 mm 0 0 25 50 75 100 125 150 175 200 MAGNETIC FLUX DENSITY in GAUSS Dwg. GH-007-1 APPLICATIONS INFORMATION Dwg. MH-011-8A Allegro These devices are normally operated in a 2-wire mode, where the supply terminal and the output terminal are tied together. An external comparator detects the change in total supply current by the addition (output off, B > BOP) or subtraction (output on, B < BRP) of IOUT. Hall effect applications information is available in the "Hall-Effect IC Applications Guide", which can be found in the latest issue of the Allegro MicroSystems Electronic Data Book, AMS-702 or Application Note 27701, or at www.allegromicro.com. TYPICAL 2-WIRE APPLICATION SUPPLY Icc + IoUT 3 0.1 F 0.85 V - + 2 V CC 100 Dwg. EH-011A X 1 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 3161 HALL-EFFECT SWITCH FOR 2-WIRE APPLICATIONS PACKAGE DESIGNATOR `LT' (SOT89/TO-243AA) Dimensions in Inches (for reference only) Dimensions in Millimeters (controlling dimensions) 0.181 0.173 0.072 0.064 0.167 0.155 0.102 0.090 0.063 0.055 0.0173 0.0138 4.60 4.40 1.83 1.62 4.25 3.94 2.60 2.29 1.60 1.40 0.44 0.35 1 2 3 0.090 0.084 1 2 3 2.29 2.13 0.047 0.035 0.059 BSC 0.0189 0.0142 0.0221 0.0173 0.118 BSC Dwg. MA-009-3A in 1.20 0.89 1.50 BSC 0.48 0.36 0.56 0.44 3.00 BSC Dwg. MA-009-3A mm 0.098 0.079 B A 0.031 0.102 0.181 3 0.047 0.031 TYP 2.5 2.0 B A 0.8 2.6 4.6 1.2 0.8 TYP 1 0.028 TYP 2 1 0.7 TYP 2 3 Pads 1, 2, 3, and A -- Standard SOT89 Layout Pads 1, 2, 3, and B -- Low-Stress Version Pads 1, 2, and 3 only -- Lowest Stress, But Not Self Aligning Dwg. MA-012-3 in Pads 1, 2, 3, and A -- Standard SOT89 Layout Pads 1, 2, 3, and B -- Low-Stress Version Pads 1, 2, and 3 only -- Lowest Stress, But Not Self Aligning Dwg. MA-012-3 mm NOTES: 1. Exact body and lead configuration at vendor's option within limits shown. 2. Supplied in bulk pack (500 pieces per bag) or add "TR" to part number for tape and reel. 3. Only low-temperature (240C) reflow-soldering techniques are recommended for SOT89 devices. www.allegromicro.com 3161 HALL-EFFECT SWITCH FOR 2-WIRE APPLICATIONS PACKAGE DESIGNATOR `UA' Dimensions in Inches (controlling dimensions) 0.164 0.159 Dimensions in Millimeters (for reference only) 4.17 4.04 45 0.062 0.058 45 1.57 1.47 0.122 0.117 45 0.031 3.10 2.97 45 0.79 0.085 MAX 1 2 3 2.16 MAX 1 2 3 0.640 0.600 0.0173 0.0138 16.26 15.24 0.44 0.35 SEE NOTE 0.0189 0.0142 SEE NOTE 0.48 0.36 0.050 BSC Dwg. MH-014E in 1.27 BSC Dwg. MH-014E mm Radial Lead Form (order A3161EUA-LC) NOTES: 1. Tolerances on package height and width represent allowable mold offsets. Dimensions given are measured at the widest point (parting line). 2. Exact body and lead configuration at vendor's option within limits shown. 3. Height does not include mold gate flash. 4. Recommended minimum PWB hole diameter to clear transition area is 0.035" (0.89 mm). 5. Where no tolerance is specified, dimension is nominal. 6. Supplied in bulk pack (500 pieces per bag). 1 2 3 0.620" 0.500" (15.7 mm 12.7 mm) 0.108" (2.74 mm) 0.100" (2.5 mm) Dwg. MH-026 NOTE: Lead-form dimensions are the nominals produced on the forming equipment. No dimensional tolerance is implied or guaranteed for bulk packaging (500 pieces per bag). 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 3161 HALL-EFFECT SWITCH FOR 2-WIRE APPLICATIONS The products described herein are manufactured under one or more of the following U.S. patents: 5,045,920; 5,264,783; 5,442,283; 5,389,889; 5,581,179; 5,517,112; 5,619,137; 5,621,319; 5,650,719; 5,686,894; 5,694,038; 5,729,130; 5,917,320; and other patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support appliances, devices, or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties that may result from its use. www.allegromicro.com 3161 HALL-EFFECT SWITCH FOR 2-WIRE APPLICATIONS HALL-EFFECT SENSORS UNIPOLAR HALL-EFFECT DIGITAL SWITCHES Partial Part Number A3121x A3122x A3123x A3141x A3142x A3143x A3144x A3161E A3240x A3361E A3362E Operate Release Hysteresis Point (G) Point (G) (G) Over Oper. Voltage & Temp. Range 220 to 500 80 to 410 260 to 430 120 to 360 230 to 470 160 to 330 30 to 175 10 to 145 115 to 245 60 to 190 205 to 355 150 to 300 35 to 450 25 to 430 <160 (Typ 130) >30 (Typ 110) <50 (Typ 35) >5 (Typ 25) <125 <125 >40 >40 60 to 150 70 to 140 70 to 140 20 to 80 30 to 80 30 to 80 >20 5 to 80 Typ 10 5 to 30 5 to 30 Oper. Temp. E, L E, L E, L E, L E, L E, L E, L E E, L E E Replaces and Comments 3019, 3113, 3119 Packages LT, UA LT, UA LT, UA LT, UA LT, UA LT, UA LT, UA LT, UA LH, LT, UA LH, LT, UA LH, LT, UA 3040, 3140 3020, 3120 2-wire operation chopper stabilized 2-wire, chopper stabilized, output normally high 2-wire, chopper stabilized, output normally low Notes: 1) Typical data is at TA = +25C and nominal operating voltage. 2) "x" = Operating Temperature Range [suffix letter or (prefix)]: S (UGN) = -20C to +85C, E = -40C to +85C, J = -40C to +115C, K (UGS) = -40C to +125C, L (UGL) = -40C to +150C. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 |
Price & Availability of 316102
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |